Product features and advantages
1. Modular design allows all wearing parts to be interchangeable, ensuring better stability in mass production and higher cost performance.
2. With modular design, production is used to replace stocking, and the delivery time is shortened by 50% compared with the original design.
3. Dry-running products feature higher cleanliness, enhanced safety and lower noise; they replace imported mechanical seals and offer better cost performance.
Parameter
| Design Pressure |
PN -0.1 ~ 0.5 MPa |
| Design Temperature |
-40 ~ 180 °C (320 °C)
When the operating temperature exceeds 180 °C, a cooling water chamber must be added, and the installation height will increase by 80 mm.
|
| Design Speed |
<2m/s |
| Medium |
Oil, water, weak acid, weak alkali and similar working conditions. |
| d |
d1 |
d0 |
D |
L1 |
L |
n-Ø |
| 30 |
116 |
150 |
180 |
16 |
100 |
4-18 |
| 40 |
135 |
170 |
205 |
16 |
100 |
4-18 |
| 45 |
164 |
200 |
235 |
18 |
105 |
8-18 |
| 50 |
164 |
200 |
235 |
18 |
105 |
8-18 |
| 60 |
164 |
200 |
235 |
18 |
105 |
8-18 |
| 65 |
164 |
200 |
235 |
18 |
105 |
8-18 |
| 70 |
164 |
200 |
235 |
18 |
105 |
8-18 |
| 80 |
188 |
225 |
260 |
18 |
105 |
12-18 |
| 90 |
220 |
255 |
290 |
18 |
105 |
12-18 |
| 95 |
220 |
255 |
290 |
20 |
105 |
12-18 |
| 100 |
245 |
280 |
315 |
20 |
105 |
12-18 |
| 110 |
245 |
280 |
315 |
20 |
105 |
12-18 |
| 120 |
245 |
280 |
315 |
20 |
105 |
12-18 |
| 125 |
245 |
280 |
315 |
20 |
105 |
12-18 |
| 130 |
245 |
280 |
315 |
20 |
105 |
12-18 |
| 140 |
280 |
320 |
370 |
24 |
110 |
12-18 |
| 150 |
312 |
355 |
405 |
24 |
125 |
12-18 |
Application areas/scenarios
As a professional mechanical seal manufacturer, we focus on serving industries such as oil and gas, chemical, pharmaceutical, food, new energy, water treatment, new materials and others.
FAQ
- Leakage (most common issue)
- Leakage at static sealing face: Check if the stationary seal gasket (O‑ring, V‑ring) is aged, deformed or mismatched in size. Replace it with a media‑resistant and temperature‑resistant gasket of the same specification. If the fit clearance between the stationary ring and the gland is too large, re‑machine or replace the stationary ring.
- Leakage at dynamic sealing face: Inspect the sealing end faces of the rotating and stationary rings for scratches, wear or chipping. Minor scratches can be repaired by lapping; replace the seal rings directly if severely damaged. Also verify the spring compression: add gaskets if insufficient, reduce gaskets if excessive.
- Leakage at shaft sleeve / shaft fit: Check for damage to the shaft sleeve gasket, or excessive fit clearance between shaft sleeve and shaft. Replace the gasket or re‑grind the shaft sleeve.
- Abnormal wear
- Excessive end face wear: Install a filter if caused by particulate impurities in the medium. For insufficient lubrication, use self‑lubricating seals such as impregnated graphite rings, or introduce external flushing liquid (e.g. clean same medium).
- Shaft sleeve wear: Replace the shaft sleeve with wear‑resistant material, and adjust the concentricity between the seal chamber and the shaft to avoid eccentric wear.
- Overheating and Burning
- Excessively high temperature in seal chamber: Check if the cooling system is clogged and clean the cooling lines. If the medium temperature is inherently high, use high-temperature resistant seal materials (such as silicon nitride ceramic rings and fluororubber gaskets).
- Poor end-face contact due to spring failure: Replace fatigued or corroded springs, select corrosion-resistant spring materials such as stainless steel, and ensure uniform spring compression.
- Vibration and Abnormal Noise
- Misalignment: Recalibrate the concentricity between the pump shaft and motor shaft, and adjust the radial runout of the seal chamber and shaft to within allowable limits.
- Loose parts: Check whether the gland bolts and drive pins are loose, tighten the bolts evenly to the specified torque, and replace worn drive pins.
- Short Service Life of Seals
- Mismatch between material and medium: Replace seal materials according to medium characteristics (e.g., Hastelloy and PTFE for corrosive media; silicon carbide for high-temperature media).
- Improper installation: Operate in strict accordance with installation specifications, avoid impact or scratches on the seal pair end faces, and ensure no impurities enter the seal chamber during installation.
